Associated-equipment 12-1015 Quick Guide Manuel d'utilisateur télécharger pdf

Battery Electrical System Analyser

(12-1015)

For testing all 12V automotive starting batteries

rated in CCA, SAE, DIN, JIS#, IEC, EN and CA.

Also for testing vehicle Electric

al System.

Quick Start Guide

Caution: Never lay tools on the

battery top. You may short the

terminals together causing harm to

yourself, the tools or the battery.

Always follow Battery Council

International safety

recommendations.

Warning: Battery terminals contain

lead compounds which is

hazardous to our body if consumed.

Please wash your hand

immediately after handling.

LIMITED WARRANTY

This Battery Electrical System Analyser [12-1015] is

warranted to be free from defects in material and

workmanship for a period of 12 months from the date

of purchase and is subjected to the following terms

and conditions:

1. Within the warranty period, the manufacturer will

repair or replace, at their options, any defective

parts and return to the owner in good working

order.

2. Any repaired or replaced parts will be warranted

for the balance of the original warranty or 90 days

from the date of repair, whichever is longer.

3. Cost of delivery charges incurred for the repair of

the product (to and from the manufacturer) will be

borne by the owner.

4. The warranty covers only the defects arises as a

result of normal use and does not cover those

arise from:

• Unauthorized modification and repair

• Improper operation or misuse

• Accident or neglect such as dropping onto

hard surfaces.

• Contact with water, rain or extreme humidity

or heat.

• Physical damages such as cables broken,

surface cracks, etc.

Performing Battery Test while it is still in the car:

Vehicle that was running has to have its engine OFF

first and then switch ON the headlights for 30 seconds

to remove the surface charge. After the headlights

had switched OFF, let the battery rest for at least 1

minute to recover before testing commences.

The car engine and all other accessory loads must be

OFF during test in order to have an accurate result.

When attaching the analyser clips, make sure that the

battery posts were not oxidized or badly corroded.

Clean them first before clamping to it. Do not clamp

onto the steel bolts directly which may give inaccurate

and inconsistent results.

Testing on stand-alone batteries:

Clean the battery posts with a wire brush prior testing.

For side- post batteries, install stud adaptors. Do not

use steel bolts for better results.

1 2 3 4 5 6 ... 10 11

Quick Start Guide 1
Alternator Test 6

Résumé du contenu

Page 1 - Quick Start Guide

1 Battery Electrical System Analyser (12-1015) For testing all 12V automotive starting batteries rated in CCA, SAE, DIN, JIS#, IEC, EN and CA. Als

Page 2

10 PRINTER SETUP 1. The printer will only work when connected directly to a 12Volt car battery because it needs higher amps than an USB port from t

Page 3

11 Then confirm it by pressing save. Once it had been saved, the display will change to the language selected. Press key

Page 4

2 1. Connect the tester clamps to the battery posts, Red to the positive (+) terminal and Black to the negative (-) terminal. Rock each clamp back a

Page 5

3 Battery: Good Measured: 406 CCA Rating: 630 CCA Volts: 12.45 V Int. R: 6.72 mOhm Life: 76% 7. Pressing again will proce

Page 6 - Alternator Test

4 12. Press key will return to the Main Menu as shown below: Grounding Test 13. Pressing  key once will scroll dow

Page 7

5 19. Now you need to press key to proceed and the display will show as follows 20. If the measured resistance reading is

Page 8

6 26. Press key to continue and the display will show as follows: 27. Switch the ignition key to ON and start cranking t

Page 9

7 33. Press key to continue and the display will show: 34. Starts the engine then press key again and the

Page 10

8 Testing with load at 2,000 RPM: This test is to check the alternator’s behavior during loading. 38. Continue from

Page 11

9 HELP KEY 43. Selecting this key will help you familiarize with the analyser by explaining the various f

Commentaires sur ces manuels

Pas de commentaire

Associated-equipment 12-1015 Quick Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Associated-equipment 12-1015 Quick Guide. Associated Equipment 12-1015 Quick Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Associated-equipment 12-1015 Quick Guide